SKU: 12307444094

PRO-TECH STRAIGHT BIT 1/4' (6.35MM) X 1'(25.4MM) TWO FLUTE LONG 1/4' SHANK KP201A

Sale price$117.38 Regular price$130.42
Save 10%

Pay in installments of $32.60 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 14 - Aug 19

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

PRO-TECH STRAIGHT BIT 1/4' (6.35MM) X 1'(25.4MM) TWO FLUTE LONG 1/4' SHANK KP201ADouble flute Straight bit In choosing a straight bit for any application, always select one with the shortest cutting edges and the shortest overall length that will reach the required cut depth. Excessive length intensifies deflection and vibration, which degrade cut quality and lead to tool breakage. Use a two flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish. Two cuts per

Double flute Straight bit

In choosing a straight bit for any application, always select one with the shortest cutting edges and the shortest overall length that will reach the required cut depth. Excessive length intensifies deflection and vibration, which degrade cut quality and lead to tool breakage.

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish.

Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

This router bit has a 6.35mm shank (shaft) that will fit most small routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

 

PRO-TECH router bits are manufactured in Taiwan. This well-supported and afforable

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection clean and scratch free
  • Hearing protection quality earmuffs
  • Dust masks discard old and dirty masks
  • Gloves for easy handling of material and hand protection
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use. 

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use. 

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet 'clicked' into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical repair centre.

 

Correct fit inside the collet

When installing the bit into the collet, do not tighten the collet with the bit 'seated.' Instead, insert the bit until the shank (bit shaft) reaches the bottom of the collet, then ease it out about 2 mm before tightening the collet.

When the bit is tightened, there should be no less than  2/3 's of the length of the shank in the collet. If your bit has a shank that is too short, then the bit should be replaced. 

 

Safety gear

There are a few other safety measures to keep in mind whenever you use your router. First of all, remember to always wear appropriate safety gear as indicated above.

Correct speed setting

Second, be sure to set your router to the proper speed for your router bit. Setting your router to an incorrect speed will not only affect the router's performance, but also can cause the bit to break much more easily and even cause bodily harm. The speed at which a router bit turns can be important. The typical router runs at about 22,000 rpm, which is fine for most bits. But as the diameter of the bit increases, you ll want to slow things down.

Also, before beginning any routing operation, be certain that you give the router's motor time to come up to full speed for the chosen setting. Beginning to cut before the bit is at full speed can give less than desired results. 

Speed Settings

Part number Shank dia. Cutting width Cutting Height Radius (r)
KP201A 1/4 in (6.35mm) 6.35 mm (1/4 in) 25.40 mm
(1.00 in)
Straight

 

Length of Shank: 32 mm
Total length: 57.4 mm (shank plus cutting height)

 

 

 



KP201ARouter Bits > Straight Bits > Imperial
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 12307444094

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.5 ★★★★★
Based on 18 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
T
Verified Purchase
TRISH RUSSO
Natrona Heights, US
★★★★★ 5
Great product
Love these. My kids got those funny pics from jc Penny's for me for Xmas. And I am surprising them with putting them on these mats.they came out wonderful
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 15, 2026
T
Verified Purchase
Tracy Hightshoe
Grantham, US
★★★★★ 5
Easy to use
Was a good purchase for the price?
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 16, 2026
S
Verified Purchase
Sam Kassa
Los Angeles, US
★★★★★ 4
Almost perfect
Great for sublimation but it is thin. Only 0.2cm if it is 0.3cm it would be perfect. I will get 0.3cm next time. Not this one.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 11, 2025
S
Verified Purchase
Silver
Houston, US
★★★★★ 5
Fantastic color and clarity! AAA+
Work amazingly well! Sublimation print was done on Epson 170 printer. 375 degrees for 60 seconds medium press. Love it! Easy to use, superb print quality and a great value for the money. They have a nice nonslip bottom.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 23, 2026
B
Verified Purchase
Betty
San Leandro, US
★★★★★ 5
Sublimation Mouse Pad blank
Great product! Nice size and sublimates very well!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 31, 2026

recommand products