SKU: 93271735279

Can-Am X3 Ring Gear Bolt Upgrade Kit by Torq Masters

$35.99 $39.99
Save 10%
No.2 Bestseller on 2pierres.com >

Pay in installments of $10.00 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Sep 11 - Sep 16

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Can-Am X3 Ring Gear Bolt Upgrade Kit by Torq MastersAC X3RGK Can Am X3 Front Differential Ring Gear Bolt Upgrade Kit The AC X3RGK Can Am X3 front differential ring gear bolt upgrade kit by Torq Masters Industries. replaces the stock Can Am ring gear bolts with upgraded M8 bolts. Also included in the kit are specialty Nord Lock locking washers and 271 High Strength Threadlocker. More about Nord Lock: Nord Lock wedge locking products are recognized around the world for their ability to secure bolted

AC-X3RGK Can-Am X3 Front Differential Ring Gear Bolt Upgrade Kit

The AC-X3RGK Can-Am X3 front differential ring gear bolt upgrade kit by Torq-Masters Industries. replaces the stock Can-Am ring gear bolts with upgraded M8 bolts. Also included in the kit are specialty  Nord-Lock locking washers and 271 High Strength Threadlocker.

 

More about Nord-Lock: Nord-Lock wedge-locking products are recognized around the world for their ability to secure bolted joints exposed to severe vibration and dynamic loads. The system cannot loosen unintentionally as it creates a wedge underneath the bolt head/nut. An ideal solution for bolted joints where failure is not an option. Nord-Lock wedge-locking technology secures bolted joints with tension instead of friction. The system comprises of a pair of lock washers that has cams on one side and radial teeth on the opposite side. {www.Nord-Lock.com}

To put it simply, Nord-Lock washers take more ft-lbs of torque to release than they do to tighten.

 

More about 271 High Strength Threadlocker: Loctite® Threadlocker Red 271™ is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces. It protects threads from rust and corrosion and prevents loosening from shock and vibration. It is only

removable once cured by heating up parts to 500°F (260°C). Recommended use on metal fasteners up to 1” (25 mm) in diameter such as bolts on decks, ready-to-assemble furniture, mounts, rings, gear bolts and frame bolts. {www.loctiteproducts.com}

 

More about Upgraded M8 Ring Gear Bolts:  This kit includes upgraded M8, ISO 4762 Hex Drive Class 12.9, Black Oxide Finish Alloy Steel Socket Cap bolts. Class 12.9 metric bolts are the highest class for strength which exceeds Grade 8.  Socket Head Cap screws are ideal for precision work with close tolerances and applications needing a well tooled appearance. Socket Head Cap screws supply greater tensile strength than equivalent Hex Head Caps screws, while requiring less surface area to counterbore. 

 Contents:

  • Qty 8, M8 Bolts
  • Qty 8, Nord-Lock Lock Washers (each washer system consists of 2 camming washers glued together)
  • Qty 1, Loctite Threadlocker Red 271
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 93271735279

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.8 ★★★★★
Based on 29 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
W
Verified Purchase
Wilderness Family
Louisville, US
★★★★★ 5
Mechanic Recommends Sea Foam -- Best Gas Treatment for All Engines
Color: Pack of 1
We have a small-engine mechanic who turned us onto SeaFoam motor treatment -- and against most gasoline preservatives and treatments. He said he'd drained, or seen inside, thousands of gasoline tanks, and the stuff sold as gasoline storage additives was often still there, sitting as gel on the bottom of the tank. Just gunk. He also said most brands of engine treatment weren't worth the money. However, he swore by SeaFoam, which I'd never tried at the time, and my experience since has proved him out. I've had many rough-running engines find their power and performance again, with nothing different, but a shot of SeaFoam in the gas tank (and the crankcase). We own a number of vehicles and equipment with small engines, from a compact backhoe, to a ride'em Husqvarna mower, weedwacker, chainsaw -- and on the larger size, a Honda SUV and Ford F150 pickup. All of them have benefited greatly from the regular use of SeaFoam. However, when we're running the road vehicles a lot, especially in the summer, we go through gas and don't necessarily add SeaFoam with every fill. Recently, the Ford began to run rough. It stalled as I pulled up to corners and lights. In the past, that would have meant a mechanic and an expensive tune-up. All I did was go for a fill-up, and started by adding a full can of SeaFoam. Problem solved, just like that. The Terramite (made in the USA) backhoe is not used a lot -- and as with most motors, that is a problem. It's bad for an engine not to run it -- and especially, in most cases, for it to sit with gas in the tank. The backhoe has a Kohler Command 25-horse gasoline engine that powers the hydraulics that run the wheels, steering, front-loader, and backhoe. I change the spark plugs each season, but it, like my Stihl chainsaw, and 6500 watt backup (gasoline) generator, and for that matter, all the small engines, can be hard to start after a hiatus. And even when they get going, they'll run rough. I used to drain the tanks frequently, then run them dry, then fill again before use, and hope for the best. But SeaFoam has changed all that. Throughout the summer, I can leave treated gas in the tank, and have little problems with starts or rough running. In the smaller equipment, I dose the gasoline with each fill (1 oz per gallon), as SeaFoam cleans both carburetors and full injection systems. It is good for gasoline and diesel engines. Added to your crankcase (1.5 oz per quart of oil), it cleans deposits and quiets noisy lifters. These days, most gasoline is mixed with ethanol and that's a bad thing for small engines. Ethanol goes hand in hand with water -- and as we all know, water in the gas is anathema to motors. Again, my small engine mechanic told me, 90% of the no-start problems he had to deal with were caused by ethanol-caused water in the fuel system. SeaFoam actually controls moisture and prevents this problem. It also de-ices and is anti-gel. In my opinion, when it comes to gasoline and diesel engines, large and small, SeaFoam is THE Silver Bullet. My equipment is often running, while my neighbors are running with theirs to the shop. I've told many about SeaFoam, but some people seem to want to do it the hard way. By the way, I also swear by PRI-G fuel additive for long-term gasoline storage. I keep 100 gallons of gas in tanks for emergency use. We are in a rural, wilderness area. I was introduced to that by survival expert, Steve Harris. He said he's had gasoline that was 10 years old still run equipment, because he'd added PRI-G to it (you can buy here on Amazon). Of course, you have to remember to add more PRI-G each year -- that's the catch. So our rule of thumb is, PRI-G for long term fuel storage -- and SeaFoam for month to month. Also -- this price is right! Of course, when you compare the cost of equipment breakdown, and having to take anything to a mechanic, this is almost free. However, apples to apples, this price is cheaper than Walmart -- and up to $4 cheaper per can than many auto supply and hardware stores. Can't say enough good things about this product! Highly recommended.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on August 19, 2015
R
Verified Purchase
Rebecca Lovegrove
Massapequa, US
★★★★★ 5
I swear by Seafoam, especially for small engines
Color: 3 Pack
I swear by Seafoam. It has really helped out my small engines, especially the 2 strokes and ones that sit around for long periods of time like my leaf blower and roto tiller. After I started adding Seafoam every time I get fuel I have had zero starting issues. They can sit all year and they will still start right up. In my car/trucks with higher miles I've used it to clean out the crankcase with great results. I add a can to the oil right before doing an oil change. I add a can then take a short drive(10 miles) to make sure the oil is up to operating temperature and change the oil once I get home. It does a good job cleaning any sludge out of the pan and the new oil stays looking fresh/clean way longer.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 4, 2026
B
Verified Purchase
B. Bordelon
Port Orchard, US
★★★★★ 5
It's Sea Foam (but not green)
Color: 3 Pack
What is there to say? If you're buying Sea Foam, you know what it is and what it does, and you're probably going to continue buying it. It's great stuff.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 21, 2026
K
Verified Purchase
Karen C
Natrona Heights, US
★★★★★ 5
Quality Champion Brand plugs
Repeat customer. Quality Champion product worth the extra $
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 12, 2026
J
Verified Purchase
Jeff
Lowell, US
★★★★★ 5
Original OEM equipment
They seem to be the copper plug required for this engine. Runs great and as it should.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 28, 2026

recommand products

Micro-precision drills / Solid carbide / Ø 1.400 mm / Company std. / Type N / TiAlN
33.38
Micro-precision drills / Solid carbide / Ø 0.140 mm / Company std. / Type N / TiAlN
25.59
Micro-precision drills / Solid carbide / Ø 1.420 mm / Company std. / Type N / TiAlN
30.03
Micro-precision drills / Solid carbide / Ø 1.070 mm / Company std. / Type N / TiAlN
30.03
Micro-precision drills / Solid carbide / Ø 0.600 mm / Company std. / Type N / TiAlN
31.25