Pay in installments of $109.10 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Sep 10 - Sep 15
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
ASM ULTIMAKER1.5.7-3D CONTROLLERUltimaker Control Board For 3D Printer similar Ramps 1. 4 RepRap compatible with Pololu Stepper Driver Boards Overview This is a board that's very similar to other Pololu based electronics implementations, including RAMPS, but it can support up to 5 steppers (three for X, Y, Z, one for an extruder and one for any other function). You can add as many stepper driver carriers as youneed. It is designed to run at higher voltages than 12 Volts, This allows
Ultimaker Control Board For 3D Printer similar Ramps 1.4 RepRap compatible with Pololu Stepper Driver Boards
Overview
This is a board that's very similar to other Pololu-based electronics implementations, including RAMPS, but it can support up to 5 steppers (three for X, Y, Z, one for an extruder and one for any other function). You can add as many stepper driver carriers as youneed. It is designed to run at higher voltages than 12 Volts, This allows you to put 90 Watts out of one MOSFET and run your stepper motors with more torque and higher maximum speeds. This board is also used on the Mantis-30 milling machine from Protospace and on various Mendel's that people have built.
Features
- Plug in all motors with simple 4-way JST connectors
- Made for Ultimaker's UltiStepper Driver.
- Compatible with Pololu stepper driver boards
- Controls up to 5 stepper motors (3 for the X, Y and Z axis one for an extruder (the "E axis"), optionally you can add another axis by adding a Pololu stepper driver.
- Configurable step sizes by placing jumpers
- 3x 55 Amp MOSFETs outputs (with LED indicators. Actual current capability limited by PCB and connectors)
- All pins are broken out for maximum extensibility
- Runs from 15V to 19V
- Three thermocouple inputs, or thermistor inputs. The 100K thermistor is recommended
- Has a IDC header for adding an LCD panel (movie here)
- Has a header for adding an SD card module
- A toggle-switch for powering up/down the board
- Easier to wire up thermocouples
- Includes a 12V regulator for an (always on) fan to cool the electronics.
- A PWM output with power for LED arrays and other lighting
- LCD backlight dimming can now be software controlled
- A serial I/O header for bluetooth and ethernet add-ons
- Servo outputs for experimental setups. They need to be interrupt or software driven as the pins routed to the servo header I/O do not have PWM
Specification
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 10 reviews
Sort
Product Reviews
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
★★★★★ 1
Unfinished product - doesn't work - waste of money
in order to use this as an installation tool the directions tell you to drill a hole through the 2 inch steel rod..... either this hole should already be drilled, or this should not be advertised as an installation tool..... it will not install any bearings without extensive modification and requires the use of a drill press or a lathe. very dissatisfied that I now have to buy ANOTHER tool just to finish this job because this one doesn't do what it's described to do.... piece of junk... typical amazon garbage.... this is why I haven't used amazon in over a year... they rip you off with garbage.... I should have known better .... don't buy this junk .... Now they say 20 -30 days to get my refund .... Don't waste your time
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 26, 2026
★★★★★ 5
Good tool, but must be hand drilled to accept bearing installation cup
Good tool, but you have to drill a hole in the bearing installation rod to accept the cross bolt that locks the bearing installation cup onto the rod.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 23, 2023
★★★★★ 5
Worked well
Worked well
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 31, 2025