SKU: 40309804955

AEM 2 Bar Brass Map Sensor Kit

$85.50 $95.00
Save 10%
No.2 Bestseller on 2pierres.com >

Pay in installments of $23.75 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 3 - Aug 8

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

AEM 2 Bar Brass Map Sensor Kit30 2131 30 30 PSIa or 2 Bar Brass Sensor Kit Accuracy: + 3% Full Scale over 40C to 105C includes Repeatability, Hysteresis and Linearity Operating Temp: 40C to 105C 40F to 221F Burst Pressure: 60PSI Response Time: < 1ms Vibration: 100 to 2000Hz, 20g Sinusoidal, 3 Axes Sensor Body: Brass Wetted Materials: 304L & 316L Stainless Steel Thread: 1 8" NPT Male Thread Weight: < 85 Grams Supply Current: Output: . 5 to 4. 5Vdc Linear Elec. Termination: Integral

30-2131-30 - 30 PSIa or 2 Bar Brass Sensor Kit

  • Accuracy: +/- 3% Full Scale over -40C to 105C includes Repeatability, Hysteresis and Linearity
  • Operating Temp: -40C to 105C / -40F to 221F
  • Burst Pressure: 60PSI
  • Response Time: < 1ms
  • Vibration:100 to 2000Hz, 20g Sinusoidal, 3 Axes
  • Sensor Body: Brass
  • Wetted Materials: 304L & 316L Stainless Steel
  • Thread: 1/8" NPT Male Thread
  • Weight: < 85 Grams
  • Supply Current:
  • Output: .5 to 4.5Vdc Linear
  • Elec. Termination: Integral weatherproof connector, includes mating connector, pins & pin lock
  • Includes: 30 PSIa or 2 Bar Brass Sensor, Connector, Pins & Pin Lock


Absolute (PSIa) Brass Pressure Sensors (See part # 30-2130-50)
AEM offer high quality brass PSIa sensors in 30(2BAR), 50 (3.5BAR) and 75 (5BAR). PSIa is referenced to absolute zero. Absolute zero is the pressure measurement when all the pressure exerted by the atmosphere has been removed. The most common use for absolute pressure sensors is reading manifold pressure. PSIa sensors are required of you wish to measure vacuum. A PSIa sensor will read about 14.7 PSI when the sensing element is exposed to atmospheric pressure at sea level however they can be recalibrated to read zero at atmospheric and a negative number at values less than atmospheric pressure.

Which Pressure Sensor is right for you?

There are many different tools that can be used for measurement, but the degree of accuracy is dependent upon the tool. For example, a ruler can measure distance with a good degree of accuracy, but for a more precise measurement a caliper should be used. The difference between a brass pressure sensor and a stainless steel pressure sensor is similar if we think about it in these terms:

AEM Brass Pressure Sensor = Ruler
Use a Brass Pressure Sensor where you need a good reference to what pressure is being seen.
Example: Brass Pressure Sensor used for a Boost Gauge – Reference/Information for knowing manifold pressure, not for ECU calibration.

Stainless Pressure Sensor = Caliper
Use a SS Pressure Sensor where you need exact details of the pressure.
Example: MAP Sensor information for the ECU – Calibration/crucial information for the ECU.

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 40309804955

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.1 ★★★★★
Based on 11 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
T
Verified Purchase
Talagand
Battle Creek, US
★★★★★ 4
Reasonably adequate room divider
Size: 4 Panel-88'', Color: Beige
I'm reviewing this as I assemble it. Couple things: 1. I didn't expect as much assembly. I've ordered dividers before and they more-or-less came as one unit. Sometimes the panels needed screwing together. These require complete assembly and come largely as three rods: two make up vertical columns and snap together. Another one (called part "C") makes the horizontal columns and you have two of these per panel (one attaches to part "A" and the other part "B"). These parts are metal with a plastic shim. Using the wood screws to attach to part "C" is a real pain in the neck. There's not much holding the panel in place so it's a little tricky. One tactic I've found while I'm assembling that works for the initial connections from parts A and B to their respective "C" rods is to hold the screw in place with a screw driver and then rotating the rod around the screw. This will do a number on your hands if you aren't wearing gloves. This obviously doesn't work when completing the connection. Using a driller driver on this is really near impossible because there isn't anything you can use to secure it in place. You can use it on the first panel, but as it gets longer, it becomes increasingly difficult and because it isn't wood, it's really tight. I considered drilling larger pilot holes but since there are only 4x4=16 screws I need to screw in, I just decided to use my screw driver to complete it. 2. Also related to assembly. When completing the panels (attaching parts "A" and "B" to parts "C" that have the cloth cover on it), you have to be careful that when you tighten that side that it isn't loosening the other side. Because the pilot holes are so tight, you can end up rotating the rod, which rotates it in the same direction as looser on the original side. Having someone hold the "C" rod in place while you screw it in is probably the easiest approach. I didn't have a 2nd person, so I just had to keep flipping back and forth and tightening both sides as I screwed it in. Not the worlds biggest deal, but annoying nonetheless. 3. The way the instructions are written, they seem to suggest building this thing progressively; that is, you do panel 1, then 2, connect them together, then do 3 and connect it, etc. I took a different route that I suspect saved me quite a bit of trouble, and I assembled all four panels first and THEN connected everything together. 4. For the love of God make sure you check that the plastic tip is on the same side for every panel. Otherwise, you have to take one side apart again and reverse it. On the bright side, if this happens, you've essentially bored out the pilot holes to be the correct size... which is having me question if I shouldn't have just bored them out to the appropriate width in the first place. 5. Attaching all of the panels together is also an enormous pain in the ass unless you happen to have an 88" long elevated surface. Attaching the legs either requires you to elevate one side, which will invariably twist the inexplicably cheap material in the bottom connectors... or you can attach them sideways... or you can put this thing upright, having two people hold the panels in place while you use the allen wrench to tighten the bolts on the underside. None of those are particularly great options. NOW on to the utility itself. 1. The panels do let some light through (I didn't believe their advertising, and that was one of the reasons that I bought beige, is that I wanted it to not be too dark). They aren't transparent though, so it isn't that far off from their description. They functionally work great, and keep the mess of wires hidden and when I'm sitting at my desk, actually reflect quite a bit of light into my office. Great! 2. My wife has described these as "the most hideous piece of furniture ever conceived of by man." So it does not have spouse approval factor. Granted, she will seldom be in my office area, so that isn't the end of the world. 3. These are really hard to align in a way that doesn't look a little tacky. There are some plastic connectors but they don't do a bang up job of keeping these in place. Each panel is slightly tilted and it's... quite obvious. I may at some point make my own improvements to these to help make them more level. It's not a particularly expensive product so I wasn't expecting much so it's fine and I'm not going to ding them on the rating because of it. All said, would I buy this product again? Probably not. It's assembly was ~90 minutes which is about 75 minutes longer than I was anticipating spending on this (not including the 5 minute writeup that I'm doing here). But am I going to return it? Also no, if for no other reason I'd be just as annoyed taking it apart and putting it in the original box to return it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 31, 2023
L
Verified Purchase
Lisa Ryan
Dallas, US
★★★★★ 5
Great product
Color: Black, Size: 4 Panel-88''
Literally exactly what I was needing
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 1, 2026
G
Verified Purchase
Grumpy
Lexington, US
★★★★★ 5
It's good...
Color: Black, Size: 4 Panel-88'', Color: Black, Size: 4 Panel-88''
It's good....took about 45 minutes to put together. No issues. Looks great...made the wife happy....
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 14, 2026
N
Verified Purchase
NettyB Variety Shoppe
Bozeman, US
★★★★★ 5
Durable non see through fabric
Color: Black, Size: 4 Panel-88'', Color: Black, Size: 4 Panel-88''
This room divider is exactly what I need. It is very durable and easy to move around. You can’t see through the fabric. I love it. My reason for purchasing this divider is to use as a divider and as a backdrop holder. And it serves both purposes perfectly. It looks much better in person than on camera. It did have the spots on one side on all of them but in a few days they went away. It foldaway and tucked away easily.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 14, 2025
B
Verified Purchase
Brittany
Bozeman, US
★★★★★ 4
Great product
Color: Black, Size: 4 Panel-88''
Love the look of this after it’s put together. It’s pretty sturdy and the connecting clips allow you to shape it different if you need it to fit in a corner. We use this at work so it’s great for the space we use it in. A little hard to store because it doesn’t fold up nicely because of the feet on it but I’m happy with it overall.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 19, 2026

recommand products

14K Solid Gold Zuni Bear Heart Line Cutout Pendant Necklace Yellow, Rose, White
184.63
ANZO 2005-2008 Dodge Magnum LED Taillights Black - 321017
177.00
Looking Home - Poster
13.95
NASA Worm T-Shirt
17.00
10K Solid Gold Lord Hanuman Hindu God Coin Pendant Necklace
159.51