Pay in installments of $13.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Aug 4 - Aug 9
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Lemon RX LM0087T DSMP 10ch Telemetry Stabilizer, T-Plug Energy MeterHighlight The generation 2 DSMP 10 channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance. DSMX DSM2 compatible, 10 channel full range telemetry stabilizer with full telemetry features including a built in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane
Highlight
The generation 2 DSMP 10-channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance.
- DSMX / DSM2 compatible, 10-channel full-range telemetry stabilizer with full telemetry features including a built-in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor
- High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
- High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
- BEC1 and BEC2 dual inputs allow high-reliability operation while improving setup for high current drain performance servo
- Built-in Delta, V-tail and Normal Wing mixer
- Supports stabilization with separated channel dual aileron operation
- Stabilization always-on feature allows nine usable channels on a 10-channel receiver
- Real-time variable stabilization gain control on channel 8
- All-channel failsafe
- Firmware health monitoring software stack and ultra-low operational voltage (3.6V) ensures high operation reliability
- Generation 2 SDR stack ensures the fastest channel searching and advanced algorithm for signal recovery with ultra-low-latency experience
- Antenna diversity improves the reliability of the wireless link
- Satellite port for additional signal diversity
- Gyro stabilization activation with either AUX2 or Gear channel
- 3 potentiometers for individual gain tuning
User manual
Reset stabilizer
- Connect power
- Hold F and B buttons (approximately 5 secs+) until all LED flashes randomly
- Press the C button. Multiple LEDs flash a few times to complete the operation
Bind with bind plug
- Insert bind plug on Channel 10
- Connect power
Bind without bind plug
- Connect power
- Hold the B button until the red LED flashes
Bind with a satellite without a bind plug
- Connect power
- Hold the B button until the red LED flashes
- Disconnect power
- Plug the satellite wire connector into the stabilizer
- Connect power
Failsafe
- Connect power to the receiver and ensure the servos are working with the transmitter
- Press the F button for 3 seconds until green changes from off to on and vice versa to change the failsafe setting. Channel value is saved as failsafe default at the time the green LED turns on.
- Turn off the transmitter and wait 2 seconds to ensure the failsafe is activated accordingly by ensuring there is torque generated with finger-pushing the servo linkage if it was to be set. Vice versa.
Stabilization activation switch
- Disconnect power
- Insert bind plug to channel 8
- Hold the C button
- Connect power. Wait for about 1 second until the 6 LEDs flash.
- Release the C button
- Press C to make changes within 3 seconds. Green = CH7, Blue = CH5.
- Wait for 3 seconds and remove the bind plug
Wing Mode and Dual Aileron
- Disconnect power
- Insert bind plug to channel 9
- Hold the C button
- Connect power. Wait for about 1 second until the 6 LEDs flash
- Check the receiver label/user manual to understand the referred LEDs' operation
- Release the C button
- Observe which red LED is flashing and brief press C to select the required mode
- Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
- Wait for 3 seconds and remove the bind plug
- Ensure transmitter mixing is set accordingly for dual aileron if stabilized dual aileron is to be configured.
Gyro direction
- Check the receiver label/user manual to understand the referred LEDs' operation
- Connect power and wait 1 second
- Hold the C button and wait for about 1 second until the 6 LEDs flash
- Release the C button
- Observe which red LED is flashing and brief press C to select the required mode
- Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
- Wait for 3 seconds and remove the bind plug.
V/I sensor calibration
- Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
- Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
- Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
- Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
- Press F or C button briefly
- Observe 3 red LED flashes
- Turn on the DC loading device by throttling the transmitter. Ensure 4A is drawing across the V/I sensor. Be careful with the motor spinning if it is to be used.
- Press the B button to save and exit.
V/I probe calibration
- Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
- Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
- Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
- Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
- Press F or C button briefly
- Observe 3 red LED flashes
- Press the B button to save and exit.
Gain setting
- Adjust via the 3 dials or real-time master gain on channel 8 depending on the transmitter channel's availability.
View setting LEDs with all on
- Press the C button briefly (no more than 2 seconds).
Lemon Rx products are tested to be compatible with Spektrum's DSMX and or DSM2 product (Spektrum, DSMX and DSM2 are the registered trademark of Horizon Hobby, Inc.).
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.7 ★★★★★
Based on 7 reviews
Sort
Product Reviews
★★★★★ 1
WARNING - EXTREMELY SHARP AREAS
Color: Yellow Nylon Corn on the Cob, Color: Yellow Nylon Corn on the Cob
UPDATE: The 2nd one I ordered was exactly the same with the sharp parts in the same areas as the first one. I cannot stress enough that a few points are sharp enough to cut or badly scratch. So if you’re planning on putting some food on it so your pup can lick, this is not the product you want! This could still scratch or cut the gums if used as a chew toy too though. I was thinking about sanding the sharp points but then I have no idea if that exposes any chemicals somehow? Really wanted this to work out!
I took this corn on the cob toy out of the plastic to wash it and before I even got to the sink I realized there were several areas that are super sharp. A few sharp enough that could cut or badly scratch! It was sealed in a plastic bag and shows no signs of being used so this defect must happen at the manufactures level. I added a video showing how easily it snags a cotton ball, cotton pad and even a beanie. Please thoroughly check your item before giving it to your pup! I was so excited to put some smashed banana on this thing and give it to my guy and thank god I checked it first! I’m going to return it and see if a 2nd one is any better and I’ll update if it is or isn’t. Also, the super sharp spots were very hard to photograph which is why I added the video.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 1, 2021
★★★★★ 4
Nice toy
Color: Red Nylon Yellow Hotdog
It is cool, tough and hard. Just wish it was larger bc my dog is 80 pounds. It won’t fall apart in a day and made in the USA!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 14, 2024
★★★★★ 5
good purchase
Color: Red Nylon Yellow Hotdog
This thing is great for hi anxiety dogs and dogs that ned to have something to do or to chew. It will take them a while to get through to it. I was told that it was indestructible but I knew if there was a dog that could do it, it would be mine, and she did. But it took her some time. But she loves it and it keeps her busy.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 24, 2025
★★★★★ 5
Cute and durable!
Color: Red, Color: Red
My dog absolutely loves this toy! I'm not sure why people are complaining it's too hard, it's a nylon dog chew toy, it's supposed to be hard. I love the little holes in the lattice top I can stuff with treats. It keeps my very (VERY) active dog busy for a long time. I would definitely recommend this if you have a power chewer. It's also super cute, I just love to see him tote around a piece of pie.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 15, 2021
★★★★★ 5
Excellent product.
Color: Red Nylon Yellow Hotdog
Excellent product. Dogs loved it!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 6, 2026