Pay in installments of $12.25 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 29 - Aug 3
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Lemon RX LM0087VP DSMP 10ch RX Telemetry, Stabilizer & Voltage ProbeHighlight The generation 2 DSMP 10 channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance. DSMX DSM2 compatible, 10 channel full range telemetry stabilizer with full telemetry features including a built in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane
Highlight
The generation 2 DSMP 10-channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance.
- DSMX / DSM2 compatible, 10-channel full-range telemetry stabilizer with full telemetry features including a built-in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor
- High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
- High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
- BEC1 and BEC2 dual inputs allow high-reliability operation while improving setup for high current drain performance servo
- Built-in Delta, V-tail and Normal Wing mixer
- Supports stabilization with separated channel dual aileron operation
- Stabilization always-on feature allows nine usable channels on a 10-channel receiver
- Real-time variable stabilization gain control on channel 8
- All-channel failsafe
- Firmware health monitoring software stack and ultra-low operational voltage (3.6V) ensures high operation reliability
- Generation 2 SDR stack ensures the fastest channel searching and advanced algorithm for signal recovery with ultra-low-latency experience
- Antenna diversity improves the reliability of the wireless link
- Satellite port for additional signal diversity
- Gyro stabilization activation with either AUX2 or Gear channel
- 3 potentiometers for individual gain tuning
User manual
Reset stabilizer
- Connect power
- Hold F and B buttons (approximately 5 secs+) until all LED flashes randomly
- Press the C button. Multiple LEDs flash a few times to complete the operation
Bind with bind plug
- Insert bind plug on Channel 10
- Connect power
Bind without bind plug
- Connect power
- Hold the B button until the red LED flashes
Bind with a satellite without a bind plug
- Connect power
- Hold the B button until the red LED flashes
- Disconnect power
- Plug the satellite wire connector into the stabilizer
- Connect power
Failsafe
- Connect power to the receiver and ensure the servos are working with the transmitter
- Press the F button for 3 seconds until green changes from off to on and vice versa to change the failsafe setting. Channel value is saved as failsafe default at the time the green LED turns on.
- Turn off the transmitter and wait 2 seconds to ensure the failsafe is activated accordingly by ensuring there is torque generated with finger-pushing the servo linkage if it was to be set. Vice versa.
Stabilization activation switch
- Disconnect power
- Insert bind plug to channel 8
- Hold the C button
- Connect power. Wait for about 1 second until the 6 LEDs flash.
- Release the C button
- Press C to make changes within 3 seconds. Green = CH7, Blue = CH5.
- Wait for 3 seconds and remove the bind plug
Wing Mode and Dual Aileron
- Disconnect power
- Insert bind plug to channel 9
- Hold the C button
- Connect power. Wait for about 1 second until the 6 LEDs flash
- Check the receiver label/user manual to understand the referred LEDs' operation
- Release the C button
- Observe which red LED is flashing and brief press C to select the required mode
- Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
- Wait for 3 seconds and remove the bind plug
- Ensure transmitter mixing is set accordingly for dual aileron if stabilized dual aileron is to be configured.
Gyro direction
- Check the receiver label/user manual to understand the referred LEDs' operation
- Connect power and wait 1 second
- Hold the C button and wait for about 1 second until the 6 LEDs flash
- Release the C button
- Observe which red LED is flashing and brief press C to select the required mode
- Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
- Wait for 3 seconds and remove the bind plug.
V/I sensor calibration
- Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
- Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
- Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
- Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
- Press F or C button briefly
- Observe 3 red LED flashes
- Turn on the DC loading device by throttling the transmitter. Ensure 4A is drawing across the V/I sensor. Be careful with the motor spinning if it is to be used.
- Press the B button to save and exit.
V/I probe calibration
- Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
- Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
- Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
- Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
- Press F or C button briefly
- Observe 3 red LED flashes
- Press the B button to save and exit.
Gain setting
- Adjust via the 3 dials or real-time master gain on channel 8 depending on the transmitter channel's availability.
View setting LEDs with all on
- Press the C button briefly (no more than 2 seconds).
Lemon Rx products are tested to be compatible with Spektrum's DSMX and or DSM2 product (Spektrum, DSMX and DSM2 are the registered trademark of Horizon Hobby, Inc.).
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.4 ★★★★★
Based on 10 reviews
Sort
Product Reviews
★★★★★ 3
They are using different/cheaper shredded foam then they were 1 year ago
Color: Memory Pillow, Size: Standard, Color: Memory Pillow, Size: Standard
The shredded foam used last year was really nice and soft and even firm to a point where your head is supported perfectly while you sleep. now the 2 extra pillows I received this weekend have completely different shredded foam which seems to be cheaper. Also when you unzip the pillow cover and get to the part where you can unzip the other cover where the foam is no longer is there. so they are using cheaper shredded foam and a cheaper cover to where the foam is and you can no longer unzip the second cover to see the foam. but I can easily tell that they are using different and cheaper foam which isn't true memory foam. their new blend is too fluffy and the pillows are floppy and too soft. the old ones i bought 1 year ago are heavy pillows that are true memory foam which your head molds into perfectly and are amazing. these new ones they are making aren't worth it. In one picture you can see the cover with different colored cheap foam and the other picture with the green and white thick premium quality shredded memory foam. The other pictures show how the old ones are thick and firm and moldable for you head and the other 2 are floppy because they use cheaper shredded foam. They need to use the shredded foam they used last year! it was really good! Now they are not true memory foam pillows anymore due to changing from premium shredded foam to cheap shredded foam.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 18, 2024
★★★★★ 5
Great comfortable, pillows.
Color: Black(4pack), Size: Standard
These are some great, comfortable pillows. They are soft and feel great. They are good for sleeping on or just using them to be comfortable in bed.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 23, 2026
★★★★★ 5
Enjoyable
Color: Grey, Size: Queen
Holds their shape and stay cool.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 24, 2026
★★★★★ 5
Cooling pillow
Best pillow I’ve used in years
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 8, 2026
★★★★★ 4
Nice pillows to sleep on
Nice to sleep on
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 31, 2026