SKU: 64712897604

upTOP TRUSS Soft Top Bed Rack For Tacoma (2005-2022)

$719.54 $799.49
Save 10%
No.2 Bestseller on 2pierres.com >

Pay in installments of $199.87 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Sep 4 - Sep 9

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

upTOP TRUSS Soft Top Bed Rack For Tacoma (2005-2022)Fully built out of aluminum our bed rack is strong, lightweight, and fits perfectly on your Tacoma over your soft topper! This rack is durable enough to mount a roof top tent without sacrificing removing your soft topper. It is offered with adjustable height legs and with a one size fits all design we cover both short and long bed owners! All upTOP TRUSS systems come complete with load bearing armor plates for both sides that are pre drilled in the

Fully built out of aluminum our bed rack is strong, lightweight, and fits perfectly on your Tacoma over your soft topper! This rack is durable enough to mount a roof top tent without sacrificing removing your soft topper. It is offered with adjustable height legs and with a one size fits all design we cover both short and long bed owners! 
All upTOP TRUSS systems come complete with load bearing armor plates for both sides that are pre-drilled in the perfect locations for mounting all your adventure and recovery gear. You'll find provisions for Maxtrax, Rotopax, Quick Fists, and Waterports. There are enough slots to allow you to attach just about anything else you can drum up a reason to take into the great unknown! 

iKAMPER rooftop tents require specific brackets, please call for details.

THIS SYSTEM ALLOWS OPERATION OF SOFT TOPPER MOTION ON THE SHORT BED MODELS ONLY. LONG BED/FULL SIZE FITMENTS WILL NOT ALLOW THE MOTION OF THE TOPPER DUE TO INTERFERENCE WITH THE REAR LOAD BAR.
NOT COMPATIBLE WITH EX CAP RACKS.

TRUSS HEIGHT  (Measured from bed rail to top of load bar). Adjustable from 21.25"-24.25". 

Included

  • (6) TRUSS Legs
  • (6) Steel Mounting Feet
  • (4) Side Armor Plates
  • (3) 2" X 2" Load Bars
  • (1) All required fasteners, washers, lock nuts, and spacers are included in the kit.

Not Included
- RETRAX bed cover, upTOP eX Overland Rack, Lighting, Maxtrax Mounts as well as anything not listed above.

Notes: The TRUSS systems sit on your existing plastic bed side rail caps under the the soft top mounting rails and bolts into the factory cargo slides located inside your Tacoma bed. All hardware, washers, and threaded inserts are included with the kit.

Middle load bar must removed to operate soft topper. Designed to operate with front and rear load bar only. Dynamic weight load is 300 pounds and static will exceed the bed rails. Please load responsibly.

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 64712897604

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.3 ★★★★★
Based on 13 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
N
Verified Purchase
Nc
Belleville, US
★★★★★ 4
Pretty good, take your time and install it well
Size: side table leg
Materials are pretty solid, but once assembled it’s not as sturdy as you would think it should be since the material itself was solid, i say give them a chance, everything out there that’s similar is way over priced
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 4, 2026
R
Verified Purchase
Roberta Mayes
San Leandro, US
★★★★★ 5
Heavy duty legs for table.
Size: side table leg
Perfect legs for a table I am having made. I have an cottonwood slice. It's heavy and needed something substantial. These are perfect.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 25, 2026
R
R. Moheban
Boise, US
★★★★★ 5
Robust pipe & fittings with a beautiful, smooth black finish
Size: side table leg
This set of pipe & fittings for use as low table legs is heavy duty and aesthetically pleasing. Especially when the pieces are handled, the tactile sensation is much nicer than with plumbing steel pipe because this product is beautifully finished smooth. The black pipes are quite smooth as well as the fittings. The pieces are all also pretty robust, though the wall thicknesses are less than in pipe for pressurized water systems. Of course that makes sense as this product does not need to hold fluid pressure. In my view they got the heaviness factor of this product just right; it's not as heavy or robust as black pipe used in natural gas supplies, but still robust and pretty heavy. Assembled, this product is absolutely stiff and unyielding for a solid table that could hold a man's weight easily. The feet utilize a brilliant scheme so that each foot can be independently adjusted for an uneven floor. Thus a level table on an uneven floor is easily accomplished. The feet simply extend the effective leg length by screwing counter-clockwise. To prevent any shifting at the threads adding some pipe compound or teflon tape may be advised. Even masking or duct tape might work as the idea is to just fill any gaps where male threads meet female threads. The four flanges at the tops of the legs provide a wide, solid surface for attaching the table top, with either hidden screws underneath or you could through-bolt a glass table top (provided you have the skill to drill glass!). I think this product would look great with a glass top. Assembly is quick and easy. The hardest part is drilling holes underneath the table top to accept screws. No pipe wrenches are needed as the pieces screw together by hand to an adequate tightness. If any doubt whether they are tightened enough have a strong person with grippy gloves finish. The "X" in the center attaches to the legs with a very clever machine screw system tightened with the included hex wrench. This is presumably because if tightened simply by screwing the fittings, the point of snugness would not likely be where the "T" fittings are exactly vertical. The maker has solved this problem so that you are assured that all legs will be in the perfect vertical position once everything is tight. The setup is also nice and rigid once tightened. This is a huge benefit of steel pipe projects; they are really solid. The black finish is clearly very durable, like a powder coat. It appears that it will provide excellent protection against rust. Coverage is complete; I found no dings or scratches anywhere on any piece. Overall this is a very well-designed product for function and aesthetics. Perfect for a beautifully renovated warehouse condo where an industrial vibe is desired in a rock-solid table that won't shift around. The smoothness of the pipe is top notch. I've used lots of pipe in projects, some of it actual water pipe and some decorative pipe such as this. I've never seen better quality decorative pipe as this maker put in the effort to finish it beautifully smooth. At currently $34.99 I find the price quite reasonable too.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 18, 2026
P
Verified Purchase
patricia
Lowell, US
★★★★★ 3
the height is only 16"
Size: coffee table leg
The height is only 16". From the description it appears to be 24" wide and 24" high.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 2, 2026
C
CMC20
Draper, US
★★★★★ 4
Good DIY Pipe Legs but Powder Coat Quality Lacks
Size: side table leg, Size: side table leg
These industrial style pipe legs make building a DIY end table easy and the kit saves a trip to the hardware store. The fittings go together normally and assembly is simple. Comes individually wrapped. My main issue is the powder coating looks and feels cheap and rubs off easily. The pipes already had marks from touching each other from unboxing. If you do not mind some wear on the finish over time this is a decent purchase. The metal at the hardware store will be thicker and more durable but will cost more. I’d recommend based on ease of having a kit and it being delivered saving me a trip.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 30, 2025

recommand products

16" Toweling - Rosie Strawberries
11.00
Animal Park Fun - Animal Stuffies Panel
17.99
Floral Fondant - Layer Cake
52.00
Field of Flowers - Floral Scatter - Peacock
14.99
Homage - Tea Time - Marmalade
14.50