SKU: 41346010011

SpeedyBee F405 Mini BLS 35A 20x20 Stack

$71.99 $79.99
Save 10%
No.2 Bestseller on 2pierres.com >

Pay in installments of $20.00 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Sep 17 - Sep 22

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

SpeedyBee F405 Mini BLS 35A 20x20 Stack$59. 99 for a Bluetooth 35A Stack? Thats ridiculous! Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4 level battery voltage display, built in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs. 35A 4 in 1 BLHeliS Mini

$59.99 for a Bluetooth 35A Stack? That’s ridiculous!
Utilizing an upgraded F405 flight controller chip with better performance than the F411, it features a built-in Bluetooth chip for seamless wireless Betaflight tuning. The board comes with a 4-level battery voltage display, built-in barometer, and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.
35A 4-in-1 BLHeliS Mini ESC: This ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.
Tune Flight controller and ESC wirelessly!
Power the quad, connect the SpeedyBee app via Bluetooth, configure the UART Ports,PID,OSD and every other settings on this flight controller. Also, every parameter of the BLHeli_S ESC in this stack can be set via the app.
With this Bluetooth stack, even micro drones become easy to tune—no need to worry about the hassle of inserting USB cables into the flight controller. Simply tune your drone wirelessly through the App, and say goodbye to wires and worries!
Powerful Real 35A 4-in-1 ESC!
6-layer 2oz PCB plus optimized circuit design equals stable and strong current output. The four-channel continuous 140A output can reach 30 seconds*.
The use of Japanese TDK filtering SMT capacitors and the onboard TVS protective diode, further enhances your flight experience, providing a seamless and reliable performance. The stack underwent rigorous pressure testing with various 5-inch freestyle and racing drones, confirming its powerful capability to effortlessly drive any 2-4 inch and lightweight 5-inch drones.
Clean Gyroscope Power Supply, Smoother Flight
Equipped with the renowned brand MaxLinear's LDO power supply chip, the gyroscope receives independent power, boosting surge protection capacity by 320%. Additionally, built with a 100uF ultra-large filtering tantalum capacitor, guarding the gyroscope's data from interference caused by the power source. Each posture and movement during flight receives precise responsiveness, allowing you to fully experience the pure beauty of flying!
Forgot your LiPo checker? Just look at the FC!
On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on goggles to check the battery status.
Change motor directions wirelessly!
Are you still using a computer to change motor directions? With this stack, when you finish your build, connect to the SpeedyBee app, change the motor directions just in a few simple steps*. Then take off.
* To use this feature, go to the App > Motors > Motor Direction Settings.
Support DJI Digital Video Transmitter
The flight controller has two independent 9V 3A BEC and 5V 2A BEC, supports various analog image transmissions above 5V, and also supports DJI O3 Air Unit/Link / Vista/Air Unit V1
M2 or M3? Why not both?
Have you ever experienced that the stack holes of your frame did not fit the stack you got? This stack is perfectly compatible with M2/M3 screws. What’s more, two sets of M2 and M3 screws + silicone grommets are included in the package!
TVS Protective Diode + 470uF Low-ESR Capacitor = Upgraded ESC Protection
The ESC is built with TVS protective diode to absorb the voltage spike when you plug in the battery, or during crashes that block your props. We also provide a Rubycon 470uF Low-ESR capacitor, ensuring clean data from the gyro to the FC.
And packaged with more useful features
● Sufficient 4 x UARTs for your receiver + VTX + camera + GPS.
● Two independent 5V 2A BEC and 9V 3A BEC.
● Power your GPS with a USB cable - no battery needed. No extra heat, no worries
● 17mm cutouts for FPV camera in your tight build
● Onboard barometer for real-time altitude sensing
● Onboard 8MB Blackbox storage
Specs Overview
Product Name SpeedyBee F405 Mini BLS 35A 20x20 Stack
Flight Controller SpeedyBee F405 Mini
ESC SpeedyBee BLS 35A Mini V2 4-in-1 ESC
Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
WiFi NOT Supported
Wireless FC Firmware Flashing NOT Supported
Wireless Blackbox Dwonload & Analysis NOT Supported
Power Input 3-6S LiPo
Mounting 20 x 20mm 3.5mm hole size，Compatible with M2 and M3 screws/Silicone grommets
Dimension 32mm(L) x 35mm(W) x 14.2mm(H)
Weight 13.5g
Specifications
ProductName SpeedyBee F405 Mini Flight Controller
MCU STM32F405
IMU(Gyro) ICM42688P
USB Port Type Type-C
Barometer Built-in
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
Wireless FC Firmware Flashing NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update
Wireless Blackbox Dwonload & Analysis NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis.
WIFI Not supported
DJI Air Unit Connection Way Direct soldering
DJI Air Unit Compatibility Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.
Blackbox 8MB Onboard Flash
BetaFlight Camera Control Pad Yes(CC pad on the front side)
Current Sensor Input Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
Power Input 3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller.
5V Output 4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output 1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V Output Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal M1 - M4 wires or soldering pads on bottom side.
UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry UART R5(UART5)
I2C Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
RSSI Input Not Supported
Smart Port / F.Port Not Supported
Supported Flight Controller Firmware BetaFlight(Default), INAV
Firmware Target Name SPEEDYBEEF405MINI
Mounting 20 x 20mm 3.5mm hole diameter ，Compatible with M2 and M3 screws/Silicone grommets.
Dimension 30(L) x 32(W) x 7.8(H)mm
Weight 9.6g
ProductName SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC
Firmware BLHeli_S J-H-40
Continuous Current 35A * 4
Burst Current 45A(5seconds)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT(Battery voltage, used to power the flight controller)
Current Sensor Support (Scale=250 Offset=-500)
ESC Telemetry Not supported
Mounting 20 x 20mm ∅3.5mm hole size，compatible with M2 and M3 screws/Silicone grommets.
Dimension 35 * 35 * 5.5mm
Weight 7.2g
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 41346010011

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.9 ★★★★★
Based on 19 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
M
Verified Purchase
Mitch
Chelsea, US
★★★★★ 5
Our German Sheppard loves these
Size: Medium
These cost a bit more than tennis balls, but they are so much nicer and longer lasting. For starters, they stay cleaner than tennis balls because they’re smooth rubber. Dirt won’t build up on them and if anything does stick, like grass or soil, it falls off once the dog slobber dries. They’re also thick, so they don’t fall apart or blow out like a normal tennis ball does in our dog’s jaws after 30 seconds. Our GS chomps on these like crazy and the only damage they’ve suffered is a crack that developed from the edge of the hole, but the crack is growing very slowly and none of these balls have totally failed yet. The balls do whistle when thrown ant high speed and that may help a dog track and locate it, but I’m not sure. Our neighbors hear the whistling too so it’s far from silent. Lastly the orange ball is easy to locate out in our yard, but the dark blue practically disappears.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 6, 2025
C
Verified Purchase
Casey B
Lowell, US
★★★★★ 5
Great for smaller dogs
Size: Small
These two balls are perfect for the smaller mouthed dog that loves to play fetch. These balls are not only super durable (lots of teeth biting), but float in the baby pool we use for our miniature dachshunds. The value here is much better than you’d find anywhere else. The noise, if bitten hard enough, was “low” at best. Easy to spot/find if overthrown. Will definitely buy again once these are in bad repair; so far, so good-love these for my fur babies!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 8, 2024
E
Verified Purchase
E. Schall
Dallas, US
★★★★★ 5
My dogs favorite balls
Size: Medium
These are great for my dog who always has to have a ball in her mouth. Not too hard so I don't have to worry about her teeth. They last for ever. They do lose their shape a little over time (like I said, she always has a ball in her mouth) they become a little oval in shape. They still bounce, she still chases it and she still chews on it so I don't think she notices or cares. I've gotten her a bag full of these over time and I have only seen one that she chewed a chunk out.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 28, 2023
K
Verified Purchase
Kimmie is happy
Bozeman, US
★★★★★ 5
My Dachshunds Love These
Size: Small
These balls are durable, flexible material, highly chewable without being easily destroyed. I stuff them with Milkbone Maro Snacks, which are just the right size to twist into the holes in the ball. My dogs literally get an hour+ chewing and chasing entertainment from these. They chew them, they sometimes 'pop' out of their mouths, go rolling across the floor, dogs chasing them. This satisfies their urge to hunt prey. Dachshunds can easily tear this kind of stuff-it-toy apart. These have lasted for a long time without tearing or shredding. I would NOT recommend them for a dog much larger than a tweenie weenie. They're a bit on the small side and might be swallowed by a larger dog. It would be cool it they also came in a larger size (and probably ball wall thickness also) for the bigger dogs to enjoy. These stuff-it chew balls are better than the kong balls my dogs had before these. Highly recommend them.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 19, 2024
L
Verified Purchase
LJ
Waukegan, US
★★★★★ 5
My puppy’s favorite fetch toy!
Size: Small
Update Aug 27, 2024: After 10 months, these are still his favorite ball. He’s obsessed with fetching and plays with them all day. They do bounce really high. Unfortunately, the small size aren’t available for sale anywhere anymore. I tried the medium size, and he has a bit of trouble hanging on to them, but he manages. Weirdly, he prefers the orange one, but he also plays with the blue one. My 7 month old Shih Tzu puppy loves to fetch, and these are his new favorites. They’re small enough to fit in his mouth, and they are made of hard plastic, so he’s able to hold on to them. They have a lot of bounce, and this adds to the fun for him. I highly recommend them.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 17, 2023

recommand products

Disc Brake Rotor Centric Parts 120.40042
105.87
Method MR317 20x9 +18mm Offset 6x5.5 106.25mm CB Matte Black Wheel
207.87
Method MR301 The Standard 17x9 -12mm Offset 5x4.5 83mm CB Matte Black Wheel
152.12
Kensington Smartfit Sit/Stand Desk
265.48
Method MR312 17x9 -12mm Offset 6x5.5 106.25mm CB Matte Black Wheel
182.64