Pencil Ignition Coil 3-Pin for Haval H2 & H6 1.5T GW4G15B - MAP-101015 / MAP-101016

Vehicle Fitment & Part Details

3-pin pencil ignition coil with suppressor for Haval / GWM 1.5T GW4G15B petrol engines across H2 FWD, H2 AWD, and H6 1.5T. Two versions of this coil are available for the same engine family — they differ only by bolt hole position on the coil body. Match your original coil's bolt hole location to the correct SKU below before ordering. Confirm compatibility by matching the listed fitment details, OEM reference numbers, and VIN/engine information where variants exist.

Which Coil Do I Need? (SKU Comparison)

Key Details

SKUs

MAP-101015 (side bolt) / MAP-101016 (rear bolt)

Component

Pencil Ignition Coil

Configuration

Single cylinder, with suppressor

Connector

3-pin

Primary Fitment

GWM / Haval H6 1.5T (GW4G15B) petrol (2014-)

OEM Reference Numbers

• Haval: 3705100-EG01T
• Haval: 3705100F0000

Vehicle Fitment

Fitment Notes

• Critical: These two SKUs are NOT interchangeable. Match your original coil's bolt hole position (side or rear) before ordering — the connector, 3-pin layout, and vehicle fitment are identical, but the bolt hole location determines which version bolts up to your specific engine loom bracket.
• Remove one coil from your vehicle first and inspect where the bolt hole sits on the coil body: if the bolt hole is on the side of the coil, order MAP-101015; if it is on the rear, order MAP-101016.
• One ignition coil is required per cylinder. The GW4G15B is a 4-cylinder engine — a full replacement therefore requires four coils of the correct type.
• Always match OEM reference number(s) and vehicle details before ordering. Confirm exact fitment using VIN, engine code, or chassis number if multiple variants exist.

Installation / Use / Maintenance Tips

• Replace all four coils as a set where possible — mixing old and new coils can cause uneven ignition performance and misfire codes.
• Inspect spark plugs at the same time; a failing coil may have damaged the plug electrode. Replace spark plugs with the correct NGK/Champion/OEM-equivalent type and gap for the GW4G15B.
• Do not over-tighten the coil mounting bolt — the coil housing and bracket are plastic/composite and will crack.
• Ensure the coil connector locks firmly into place; a loose connector causes intermittent misfire under vibration.
• Clear any stored misfire DTCs (P0300-P0304) with a scan tool after replacement and confirm no codes return after a short road test.

Common Questions

Which SKU do I need — MAP-101015 or MAP-101016?
Remove one coil from your engine and look at where the mounting bolt hole is on the coil body. If the bolt hole is on the side, order MAP-101015. If the bolt hole is on the rear, order MAP-101016. Both are 3-pin single-cylinder pencil coils with suppressor, and both fit the same GW4G15B engine — only the bolt mounting position differs.

Will this ignition coil fit my Haval H2 or H6?
Yes, provided your vehicle has the GW4G15B 1.5T petrol engine. Confirm the engine code on the engine or via VIN lookup, then choose the correct SKU based on bolt hole position.

Are MAP-101015 and MAP-101016 interchangeable?
No. Although they fit the same engine and use the same 3-pin connector, the bolt hole position is different — the wrong version will not mount correctly to your specific engine's loom bracket.

How many coils do I need per vehicle?
The GW4G15B is a 4-cylinder engine, so four coils are required for a full set. All four must be the same SKU for your vehicle.

What OEM part numbers does this cross-reference?
Cross-reference numbers are listed in the OEM Reference Numbers section above. Match at least one to your original part before ordering.

How do I confirm fitment if there are multiple variants?
Use VIN, engine code, and compare your removed coil's bolt hole position to the SKU comparison table above. If unsure, request fitment assistance before ordering.